- 您现在的位置：买卖IC网 > Sheet目录1012 > UC232R-10 (FTDI, Future Technology Devices International Ltd)CABLE USB RS232 EMBEDDED 10CM
2. Features and Enhancements of FT232R
Page 3
2.1 FT232R Key Features
This section summarises the key features and enhancements of the FT232R IC device which is used on the UC232R
“ChiPi” USB to RS232 converter cable. For further details, consult the FT232R datasheet, which is available from the
Integrated Clock Circuit - Previous generations of FTDI’s USB UART devices required an external crystal or ceramic
resonator. The clock circuit has now been integrated onto the device meaning that no crystal or ceramic resonator is
required. However, if required, an external 12MHz crystal can be used as the clock source.
Integrated EEPROM - Previous generations of FTDI’s USB UART devices required an external EEPROM if the
device were to use USB Vendor ID (VID), Product ID (PID), serial number and product description strings other than
the default values in the device itself. This external EEPROM has now been integrated onto the FT232R chip meaning
that all designs have the option to change the product description strings. A user area of the internal EEPROM is
available for storing additional data. The internal EEPROM is programmable in circuit, over USB without any additional
voltage requirement.
Preprogrammed EEPROM - The FT232R is supplied with its internal EEPROM preprogrammed with a serial number
which is unique to each individual device. This, in most cases, will remove the need to program the device EEPROM.
Integrated USB Resistors - Previous generations of FTDI’s USB UART devices required two external series resistors
on the USBDP and USBDM lines, and a 1.5 kΩ pull up resistor on USBDP. These three resistors have now been
integrated onto the device.
Integrated AVCC Filtering - Previous generations of FTDI’s USB UART devices had a separate AVCC pin - the
supply to the internal PLL. This pin required an external R-C ?lter. The separate AVCC pin is now connected internally
to VCC, and the ?lter has now been integrated onto the chip.
Less External Components - Integration of the crystal, EEPROM, USB resistors, and AVCC ?lter will substantially
reduce the bill of materials cost for USB interface designs using the FT232R compared to its FT232BM predecessor.
Con?gurable CBUS I/O Pin Options - There are now 5 con?gurable Control Bus (CBUS) lines. Options are TXDEN
- transmit enable for RS485 designs, PWREN# - Power control for high power, bus powered designs, TXLED# - for
pulsing an LED upon transmission of data, RXLED# - for pulsing an LED upon receiving data, TX&RXLED# - which
will pulse an LED upon transmission OR reception of data, SLEEP# - indicates that the device going into USB
suspend mode, CLK48 / CLK24 / CLK12 / CLK6 - 48MHz, 24MHz,12MHz, and 6MHz clock output signal options.
There is also the option to bring out bit bang mode read and write strobes (see below). The CBUS lines can be
con?gured with any one of these output options by setting bits in the internal EEPROM. The device is supplied with
the most commonly used pin de?nitions preprogrammed - see Section 8 for details.
Enhanced Asynchronous Bit Bang Mode with RD# and WR# Strobes - The FT232R supports FTDI’s BM chip
bit bang mode. In bit bang mode, the eight UART lines can be switched from the regular interface mode to an 8-bit
general purpose I/O port. Data packets can be sent to the device and they will be sequentially sent to the interface
at a rate controlled by an internal timer (equivalent to the baud rate prescaler). With the FT232R device this mode
has been enhanced so that the internal RD# and WR# strobes are now brought out of the device which can be used
to allow external logic to be clocked by accesses to the bit bang I/O bus. This option will be described more fully in a
separate application note.
Synchronous Bit Bang Mode - Synchronous bit bang mode differs from asynchronous bit bang mode in that the
interface pins are only read when the device is written to. Thus making it easier for the controlling program to measure
the response to an output stimulus as the data returned is synchronous to the output data. The feature was previously
seen in FTDI’s FT2232C device. This option will be described more fully in a separate application note.
CBUS Bit Bang Mode - This mode allows four of the CBUS pins to be individually con?gured as GPIO pins, similar
to Asynchronous bit bang mode. It is possible to use this mode while the UART interface is being used, thus providing
up to four general purpose I/O pins which are available during normal operation. An application note describing this
UC232R “ChiPi” Minimum Component FT232RL USB to RS232 Converter Cable
Datasheet Version 0.90
? Future Technology Devices International Ltd. 2005
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
UEZGUI-1788-43WQS
KIT DEV 4.3" TOUCH SCREEN
UEZGUI-1788-70WVE
KIT DEV 7" TOUCH SCREEN
UEZGUI-1788-70WVT
KIT DEV 7" TOUCH SCREEN
VDRS14T420BSC
压敏电阻 420V 17mm
UM17A6U-22
BACKPLANE 6UX17SLOT POWER BUGS
UMS05-1A80-75D
RELAY REED SPST 500MA 5V
UMS05-1A80-75L
RELAY REED SPST 500MA 5V
UN-8086
CABLE BRACKET FOR NETWORK CABINT
相关代理商/技术参数
UC232R-10-NE
功能描述:电缆组件 USB to RS232 Embeded Conv, Open PCB 10cm RoHS:否 制造商:Molex 产品:Power Assemblies 类型:Cable Assembly 连接器端口 A:No Connector 连接器端口 A 管脚计数:4 连接器端口 B:No Connector 连接器端口 B 管脚计数: 型式:Male 线规 - 美国线规（AWG）:20, 28 长度:0.305 m 颜色:Black, Red
UC-235
制造商:Brainboxes 功能描述:Serial Card, 3.3/5.0V, LP uPCI, 1 x RS232 制造商:BRAINBOXES 功能描述:CARD LOWPROFILE PCI RS232 1PORT 制造商:BRAINBOXES 功能描述:CARD, LOWPROFILE, PCI, RS232, 1PORT 制造商:Brainboxes 功能描述:LP UPCI 1XRS232 制造商:BRAINBOXES 功能描述:LP UPCI 1XRS232
UC-235
制造商:BRAINBOXES 功能描述:LOW PROFILE PCI 1 PORT RS232
UC2-3NJ
功能描述:低信号继电器 - PCB DPDT 3V NON-LATCH
RoHS:否 制造商:NEC 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 V 最大开关电流:1 A 线圈电流:1 A 线圈类型:Non-Latching 功耗:140 mW 端接类型:SMT 绝缘: 介入损耗:
UC2-3SNJ
功能描述:低信号继电器 - PCB DPDT 3V SNGL COIL
RoHS:否 制造商:NEC 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 V 最大开关电流:1 A 线圈电流:1 A 线圈类型:Non-Latching 功耗:140 mW 端接类型:SMT 绝缘: 介入损耗:
UC2-4.5NJ
功能描述:低信号继电器 - PCB DPDT 4.5V NON-LATCH
RoHS:否 制造商:NEC 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 V 最大开关电流:1 A 线圈电流:1 A 线圈类型:Non-Latching 功耗:140 mW 端接类型:SMT 绝缘: 介入损耗:
UC2-4.5SNJ
功能描述:低信号继电器 - PCB DPDT 4.5V SNGL COIL
RoHS:否 制造商:NEC 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 V 最大开关电流:1 A 线圈电流:1 A 线圈类型:Non-Latching 功耗:140 mW 端接类型:SMT 绝缘: 介入损耗:
UC24-14-34DD
制造商:Takachi Electric Industrial 功能描述:UC24-14-34DD